Upgrading your Synology DS1512+ to 3GB of RAM

1. Purchase compatible memory

The first step in your Synology DS1512+ RAM Upgrade is to acquire a compatible RAM module.

Synology states the DS1512+ supports: 2GB -DDR3-1066 unbuffered So-DIMM 204pin CL=7 1.5V

The Synology Community Forum seems to support that the Kingtson KVR1066D3S8S7/2G is the best choice for the DS1512+.  This is what I decided to go with and the upgrade went smoothly.  My DS1512+ passed all memory diagnostics and is running great with this stick of RAM.

Alternatively, there are several other User Reported Compatible RAM modules to choose from.  Just ensure that you purchase a module that is fully compatible with your DS1512+.

Kingston KVR1066D3S8S7/2G Memory

」 data-medium-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2980-300×200.jpg」 data-large-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2980-1024×683.jpg」 />

2. Remove five screws from rear of DS1512+

Using a Phillips screwdriver, remove the five screws holding the cover panel in place on the rear side of the DS1512+.

Screw hole locations on rear of Synology DS1512+

」 data-medium-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2974-300×200.jpg」 data-large-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2974-1024×683.jpg」 />

3. Slide the cover panel off

Place your thumbs on the indicated positions and then slide the cover panel toward you to remove.

Rear view of Synology DS1512+ showing where to place thumbs to slide exterior case panel off.

」 data-medium-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2975-300×200.jpg」 data-large-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2975-1024×683.jpg」 />

4. Gain Access to the expandable memory slot

Locate the expandable memory slot (pictured below)

Location of Synology DS1512+ Expandable Memory Slot

」 data-medium-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2977-300×200.jpg」 data-large-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2977-1024×683.jpg」 />

5. Insert the RAM module into the expandable memory slot

Align the RAM module with the grooves of the memory slot.  (It will only fit one way).  You will need to insert the module at an angle (shown in the picture below).

Installing 2GB of RAM into Synology DS1512+ Memory Slot

」 data-medium-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2979-300×200.jpg」 data-large-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2979-1024×683.jpg」 />

6. Lock the RAM module in place

Slowly push the RAM module down until you hear a solid click.  Note the two capture arms on both side should hold the RAM module in a locked position.

Synology DS1512+ Expandable Memory Slot with 2GB of RAM Installed

」 data-medium-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2978-300×200.jpg」 data-large-file=」http://techthoughts.info/wp-content/uploads/2013/04/IMG_2978-1024×683.jpg」 />

7. Reassemble your DS1512+

Reverse the above steps. Slide the cover panel back on and reinstall five screws to secure the cover panel

8. Power on and verify RAM upgrade

Power on your DS1512+. After a few moments you should hear a single beep indicating a successful boot. Log in to your DS1512+ and open System Information to verify that your new Synology DS1512+ RAM Upgrade is complete!

Synology DS1512+ DSM System Information

」 data-medium-file=」http://techthoughts.info/wp-content/uploads/2013/04/Upgrade-Verify-300×102.png」 data-large-file=」http://techthoughts.info/wp-content/uploads/2013/04/Upgrade-Verify-1024×349.png」 />